Cedar swing and slide set · Backyard Discovery Buckley Hill（2001046） 3D manual

Loading 3D model

Tap here

Drag to rotate · Right-click or two fingers to pan · Scroll or pinch to zoom · Tap a part for details

All done

FAQ

Stuck?
Start here.

These are the issues buyers run into most when assembling. Tap one to jump to that step in 3D.

All steps

Assemble

Choose a site and sort parts Choose level ground at least 6.56 ft (2 m) from obstacles. Check wood parts and hardware by number and replace missing parts first.
Step back side up Place step L4 with its back up, exposing the two climbing hold holes. Install the T-nuts first.
Press in both T-nuts Press 2 H100072 T-nuts into the back of the step, with the prongs embedded in the wood and the flanges flush against the surface.
Tap the nuts gently until flush Tap both T-nuts gently with a rubber mallet until the prongs fully enter the wood and the flanges sit flat.
Turn the step face up Support both step ends with your hands, lift, and turn over. Keep the T-nuts on the back and set securely front side up.
Align the climbing hold holes Place climbing holds on the fronts of the steps, alternating left and right. Align both holes in each hold.
Insert the climbing hold fasteners for tightening Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Tighten the climbing rock Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Step back side up Place step L4 with its back up, exposing the two climbing hold holes. Install the T-nuts first.
Press in both T-nuts Press 2 H100072 T-nuts into the back of the step, with the prongs embedded in the wood and the flanges flush against the surface.
Tap the nuts gently until flush Tap both T-nuts gently with a rubber mallet until the prongs fully enter the wood and the flanges sit flat.
Turn the step face up Support both step ends with your hands, lift, and turn over. Keep the T-nuts on the back and set securely front side up.
Align the climbing hold holes Place climbing holds on the fronts of the steps, alternating left and right. Align both holes in each hold.
Insert the climbing hold fasteners for tightening Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Tighten the climbing rock Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Step back side up Place step L4 with its back up, exposing the two climbing hold holes. Install the T-nuts first.
Press in both T-nuts Press 2 H100072 T-nuts into the back of the step, with the prongs embedded in the wood and the flanges flush against the surface.
Tap the nuts gently until flush Tap both T-nuts gently with a rubber mallet until the prongs fully enter the wood and the flanges sit flat.
Turn the step face up Support both step ends with your hands, lift, and turn over. Keep the T-nuts on the back and set securely front side up.
Align the climbing hold holes Place climbing holds on the fronts of the steps, alternating left and right. Align both holes in each hold.
Insert the climbing hold fasteners for tightening Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Tighten the climbing rock Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Step back side up Place step L4 with its back up, exposing the two climbing hold holes. Install the T-nuts first.
Press in both T-nuts Press 2 H100072 T-nuts into the back of the step, with the prongs embedded in the wood and the flanges flush against the surface.
Tap the nuts gently until flush Tap both T-nuts gently with a rubber mallet until the prongs fully enter the wood and the flanges sit flat.
Turn the step face up Support both step ends with your hands, lift, and turn over. Keep the T-nuts on the back and set securely front side up.
Align the climbing hold holes Place climbing holds on the fronts of the steps, alternating left and right. Align both holes in each hold.
Insert the climbing hold fasteners for tightening Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Tighten the climbing rock Tighten each hold with 2 H100063 bolts and internal-tooth washers. The holds must not rotate.
Lay the ladder uprights side by side Lay F1 and F2 flat, with the upper connection holes at the same end. Space the outsides of the uprights 16.93 in (430 mm) apart.
Steps cover the ladder uprights Place the 4 L4 steps from top to bottom, alternating left and right, with L3 at the bottom. The steps cover the fronts of both ladder uprights.
Insert the 20 ladder screws for tightening Drive 20 H100086 screws through the front of the steps into the ladder uprights. Leave bottom step L3 smooth, without climbing holds.
Tighten the 20 ladder screws Drive 20 H100086 screws through the front of the steps into the ladder uprights. Leave bottom step L3 smooth, without climbing holds.
Position the flexible slide Keep the slide face up with a helper supporting it. Face the bottom lip downward and leave room for the bottom support.
Pre-flex both slide ends Gently flex both ends of the flexible slide with both hands for later insertion into the grooves. Do not bend the rigid side rails.
Gently flex the slide ends Gently flex both slide ends just enough to match the curvature of the side rail ends.
Position the slide bottom support Keep the bottom edge of M77 1/2 in from the bottom edge of the slide. Use the two holes in the support board as a template to mark the holes.
Drill the slide bottom holes Keep M77 1/2 in from the bottom edge. Drill the two through-holes in the slide with a 3/8-inch drill bit.
Insert hardware to secure the slide bottom support Thread 2 H100115 bolts into the H100074 T-nuts on the back, keeping M77 against the bottom lip.
Tighten the slide bottom support Thread 2 H100115 bolts into the H100074 T-nuts on the back, keeping M77 against the bottom lip.
Lay the side rail flat Face the side rail groove toward the slide. Set securely and check the 8 recesses along the rail.
Predrill the 8 side rail holes At each of the 8 recesses per side rail, drill 1 pilot hole with a 1/8-inch bit, 16 holes total.
Seat the slide in the inner grooves Start at the bottom, with a helper flexing the slide. Seat the entire edge fully in the side rail groove.
Insert the center support board Insert M78 from the open side into the center recess on the back of the slide, with both ends in the matching side rail slots.
Insert the 8 side rail screws for tightening Use 8 H100090 screws per side to secure the slide and M78. Tighten each until snug without cracking the plastic.
Tighten the 8 side rail screws Use 8 H100090 screws per side to secure the slide and M78. Tighten each until snug without cracking the plastic.
Lay the side rail flat Face the side rail groove toward the slide. Set securely and check the 8 recesses along the rail.
Predrill the 8 side rail holes At each of the 8 recesses per side rail, drill 1 pilot hole with a 1/8-inch bit, 16 holes total.
Seat the slide in the inner grooves Start at the bottom, with a helper flexing the slide. Seat the entire edge fully in the side rail groove.
Insert the 8 side rail screws for tightening Use 8 H100090 screws per side to secure the slide and M78. Tighten each until snug without cracking the plastic.
Tighten the 8 side rail screws Use 8 H100090 screws per side to secure the slide and M78. Tighten each until snug without cracking the plastic.
Set the swing beam securely Place SB74 on the support surface. Install the A-frame end extension brackets first, then the tower end L-bracket.
Install both extension brackets Place A100325 and A100326 on opposite sides of the A-frame end of the beam, with the projecting tabs down. Align the 3 holes.
Insert hardware to secure the extension brackets Clamp the extension brackets on both sides of the beam with 3 H100011 bolts and 3 H100005 barrel nuts.
Tighten the extension brackets Clamp the extension brackets on both sides of the beam with 3 H100011 bolts and 3 H100005 barrel nuts.
Install the beam L-bracket Fit 2 A100140 brackets on either side of the tower end of the beam, with the projecting faces toward the tower. Align the through-holes.
Insert hardware to secure the beam L-bracket Insert 2 H100047 through-bolts with a flat washer at each end. Tighten the locknuts on the back until snug.
Tighten the beam L-bracket Insert 2 H100047 through-bolts with a flat washer at each end. Tighten the locknuts on the back until snug.
Secure the blank nameplate Place the nameplate at its designated beam location, align all 4 holes, and secure with H100128.
Insert the 4 nameplate screws for tightening Tighten 4 H100128 screws until the nameplate sits flat against the beam.
Tighten the 4 nameplate screws Tighten 4 H100128 screws until the nameplate sits flat against the beam.
Insert the hanger from below Fit a safety washer on each of the 4 H100099 hangers and insert upward through the hanging holes from below the beam.
Washers and nuts in place Place a safety washer beneath each hanger, then a flat washer and H100110 locknut above.
Tighten the hanger nuts Tighten the locknuts from above with a socket wrench until the hangers seat against the safety washers. Tighten all 4 points.
Washers and nuts in place Place a safety washer beneath each hanger, then a flat washer and H100110 locknut above.
Tighten the hanger nuts Tighten the locknuts from above with a socket wrench until the hangers seat against the safety washers. Tighten all 4 points.
Washers and nuts in place Place a safety washer beneath each hanger, then a flat washer and H100110 locknut above.
Tighten the hanger nuts Tighten the locknuts from above with a socket wrench until the hangers seat against the safety washers. Tighten all 4 points.
Washers and nuts in place Place a safety washer beneath each hanger, then a flat washer and H100110 locknut above.
Tighten the hanger nuts Tighten the locknuts from above with a socket wrench until the hangers seat against the safety washers. Tighten all 4 points.
Assemble the A-frame Place support W71 between the 2 E77 angled legs, with cross brace H79 against the outside. Align all predrilled holes.
Insert hardware to secure the A-frame top Insert H100021 through E77 and W71, with H100030 under the head and an H100005 barrel nut with H100031 on the back.
Tighten the A-frame top Insert H100021 through E77 and W71, with H100030 under the head and an H100005 barrel nut with H100031 on the back.
Insert hardware to secure the A-frame cross brace Secure H79 to the two E77 legs with 2 H100013 bolts, T-nuts, and lock washers.
Tighten the A-frame cross brace Secure H79 to the two E77 legs with 2 H100013 bolts, T-nuts, and lock washers.
Insert hardware to secure the cross brace center Secure the center of H79 to support W71 with 2 H100027 screws and lock washers.
Secure the cross brace center Secure the center of H79 to support W71 with 2 H100027 screws and lock washers.
Stand the A-frame upright With two people, stand the A-frame upright with both angled legs touching the ground together. Keep holding it steady until the beam is connected.
Connect the beam to the A-frame With two people, lift the beam and fit the extension brackets over the top of W71. Align both connection holes.
Insert hardware to secure the beam to the A-frame Tighten 2 H100011 bolts with H100005 barrel nuts while an adult supports the other end of the beam.
Tighten the beam to the A-frame Tighten 2 H100011 bolts with H100005 barrel nuts while an adult supports the other end of the beam.
Assemble the first wall Lay E1 and E2 flat. From bottom to top, they cover ground beam M5, floor joist H8, and narrow top rail N3.
Insert hardware to secure the first wall with 6 screws Secure N3 at two points and M5 at four points with 6 H100027 screws and lock washers. Drive the wood screws into the posts.
Secure the first wall with 6 screws Secure N3 at two points and M5 at four points with 6 H100027 screws and lock washers. Drive the wood screws into the posts.
Insert hardware to secure the floor joist with 3 screws Secure H8 with 3 H100028 wood screws and lock washers. There are 9 wood screws total on this face.
Secure the floor joist with 3 screws Secure H8 with 3 H100028 wood screws and lock washers. There are 9 wood screws total on this face.
Assemble the second wall Lay E3 and E4 flat, covering ground beam M1, floor joist H1, and the two N2 rails in order.
Insert hardware to secure the second wall with 8 screws Secure M1 to the two N2 rails with 8 H100027 screws and lock washers.
Secure the second wall with 8 screws Secure M1 to the two N2 rails with 8 H100027 screws and lock washers.
Insert hardware to secure the floor joist with 4 screws Secure H1 with 4 H100028 wood screws and lock washers. There are 12 wood screws total on this face.
Secure the floor joist with 4 screws Secure H1 with 4 H100028 wood screws and lock washers. There are 12 wood screws total on this face.
Stand the first wall upright With two people holding the posts, stand the first wall upright. Keep the post feet on the ground and someone holding it.
Stand the second wall upright Stand the second wall upright, with both floor joists level and post side holes aligned.
Connect the left-side wood parts Install H2, N1, and M3 on the left. Place two H4 blocks inside H2, with M3 projecting toward the ladder foot as illustrated.
Insert hardware to secure the left floor joist Insert 2 H100017 bolts through H2, the posts, and H4, using lock washers and T-nuts.
Secure the left floor joist Insert 2 H100017 bolts through H2, the posts, and H4, using lock washers and T-nuts.
Insert hardware at all 4 mounting holes to secure the left side. Secure N1 to M3 with 4 H100012 bolts, each with 1 H100030 washer and 1 H100074 T-nut.
Secure the left side at all 4 mounting holes. Secure N1 to M3 with 4 H100012 bolts, each with 1 H100030 washer and 1 H100074 T-nut.
Connect the right-side wood parts Install H2, M2, and two H4 support blocks on the right, keeping both floor joist tops level.
Insert hardware to secure the right floor joist Insert 2 H100017 bolts through H2, the posts, and H4, using lock washers and T-nuts.
Secure the right floor joist Insert 2 H100017 bolts through H2, the posts, and H4, using lock washers and T-nuts.
Insert hardware to secure the right ground beam Secure M2 with 2 H100012 bolts, lock washers, and T-nuts. There are 10 bolt sets total across both sides.
Secure the right ground beam Secure M2 with 2 H100012 bolts, lock washers, and T-nuts. There are 10 bolt sets total across both sides.
Square and level Measure both diagonals until equal. Check level front to back and side to side, then seat snugly and tighten once square.
Install the center floor supports Place center floor joist H3 first, then the two T1 pieces between the four H4 pieces. Keep their tops flush with the floor joists.
Insert hardware to secure the center support ends Drive 2 H100090 screws per end through the outside floor joists into the H3 ends, 4 total front and rear.
Secure the center support ends Drive 2 H100090 screws per end through the outside floor joists into the H3 ends, 4 total front and rear.
Insert hardware to secure the center support ends Drive 2 H100090 screws per end through the outside floor joists into the H3 ends, 4 total front and rear.
Secure the center support ends Drive 2 H100090 screws per end through the outside floor joists into the H3 ends, 4 total front and rear.
Insert hardware to secure both T1 pieces Secure each T1 to H2 from inside with 5 H100089 screws, 10 total across both sides. Keep the tops flush.
Secure both T1 pieces Secure each T1 to H2 from inside with 5 H100089 screws, 10 total across both sides. Keep the tops flush.
Insert hardware to secure both T1 pieces Secure each T1 to H2 from inside with 5 H100089 screws, 10 total across both sides. Keep the tops flush.
Secure both T1 pieces Secure each T1 to H2 from inside with 5 H100089 screws, 10 total across both sides. Keep the tops flush.
Secure the blank revision plate Place the revision plate at the designated spot on the side of H3 and secure with 2 H100128 screws.
Insert the 2 revision plate screws for tightening Tighten 2 H100128 screws until the revision plate sits flat.
Tighten the 2 revision plate screws Tighten 2 H100128 screws until the revision plate sits flat.
Lay all seven floorboards Lay L1, the 5 M4 boards, and L2 first. Orient the end holes as illustrated, with every board supported by the floor joists.
Insert the 43 floor screws for tightening Drive 43 H100086 screws down through the panel holes into the floor joists. Keep all panels flush.
Tighten the 43 floor screws Drive 43 H100086 screws down through the panel holes into the floor joists. Keep all panels flush.
Install N2 after the floor Once the floor is fully secured, place rail N2 over the outside of the front posts and align both end holes.
Insert hardware to secure rail N2 Secure N2 with 2 H100027 screws and lock washers, keeping the rail against both posts.
Secure rail N2 Secure N2 with 2 H100027 screws and lock washers, keeping the rail against both posts.
Install the side and top rails Place top rail G and the 3 N1 rails outside, with predrilled holes toward the illustrated connection ends. Keep the rails level.
Insert hardware at all 4 mounting holes to secure the top rail. Secure the top rail with 4 H100013 bolts, T-nuts, and lock washers. Tighten each connection until snug.
Secure the top rail at all 4 mounting holes. Secure the top rail with 4 H100013 bolts, T-nuts, and lock washers. Tighten each connection until snug.
Insert hardware at all 6 mounting holes to secure the side rail. Secure both ends of the 3 N1 rails with 6 H100012 bolts, T-nuts, and lock washers.
Secure the side rail at all 6 mounting holes. Secure both ends of the 3 N1 rails with 6 H100012 bolts, T-nuts, and lock washers.
Hang the safety net on the inside Place the safety net inside the posts. Align upper and lower eyelets with the predrilled wood holes.
Insert hardware at both mounting holes to secure the safety net. Insert 2 H100128 screws through the upper and lower eyelets from inside. Tighten until snug, keeping the net flat.
Secure the safety net at both mounting holes. Insert 2 H100128 screws through the upper and lower eyelets from inside. Tighten until snug, keeping the net flat.
Install the side and top rails Place top rail G and the 3 N1 rails outside, with predrilled holes toward the illustrated connection ends. Keep the rails level.
Insert hardware at all 4 mounting holes to secure the top rail. Secure the top rail with 4 H100013 bolts, T-nuts, and lock washers. Tighten each connection until snug.
Secure the top rail at all 4 mounting holes. Secure the top rail with 4 H100013 bolts, T-nuts, and lock washers. Tighten each connection until snug.
Insert hardware at all 6 mounting holes to secure the side rail. Secure both ends of the 3 N1 rails with 6 H100012 bolts, T-nuts, and lock washers.
Secure the side rail at all 6 mounting holes. Secure both ends of the 3 N1 rails with 6 H100012 bolts, T-nuts, and lock washers.
Hang the safety net on the inside Place the safety net inside the posts. Align upper and lower eyelets with the predrilled wood holes.
Insert hardware at both mounting holes to secure the safety net. Insert 2 H100128 screws through the upper and lower eyelets from inside. Tighten until snug, keeping the net flat.
Secure the safety net at both mounting holes. Insert 2 H100128 screws through the upper and lower eyelets from inside. Tighten until snug, keeping the net flat.
Lift the ladder and move to the entrance With two people holding both ladder uprights, lift the ladder and move through the clear area to the entrance, with climbing holds outward.
Rest the ladder against the platform Bring the ladder top toward H8 through the open entrance, with its feet on the ground. Rest the left foot against the projecting end of M3.
Insert hardware to secure the ladder top bolt Secure one side of the ladder top to H8 with H100010, a lock washer, and a T-nut.
Secure the ladder top bolt Secure one side of the ladder top to H8 with H100010, a lock washer, and a T-nut.
Insert hardware to secure the other ladder top Drive H100029 with a lock washer into the other side of the ladder top, keeping it against the platform beam.
Secure the other ladder top Drive H100029 with a lock washer into the other side of the ladder top, keeping it against the platform beam.
Insert hardware to secure one ladder foot Drive H100027 with a lock washer through the outside of M3 into the ladder upright. Keep the ladder foot on the ground.
Secure one ladder foot Drive H100027 with a lock washer through the outside of M3 into the ladder upright. Keep the ladder foot on the ground.
Place the top ladder step Place L5 at the top of both ladder uprights, with its upper edge meeting the platform. Align the four holes with the uprights.
Insert hardware to secure the ladder top with 4 screws Drive 4 H100086 screws through the front of L5 into the ladder uprights. Keep the top step from lifting.
Secure the ladder top with 4 screws Drive 4 H100086 screws through the front of L5 into the ladder uprights. Keep the top step from lifting.
Connect the other ladder foot Connect M6 to the tower along the other ladder foot. Place bracket A4M01046 at the junction of the ladder foot and M6.
Insert hardware to secure the rear end of M6 Secure the rear end of M6 to ground beam M5 with H100027 and a lock washer.
Secure the rear end of M6 Secure the rear end of M6 to ground beam M5 with H100027 and a lock washer.
Insert hardware to secure the ladder foot bracket outer leg Secure the bracket to M6 with 1 H100115 bolt, an H100004 barrel nut, and an H100031 washer.
Tighten the ladder foot bracket outer leg Secure the bracket to M6 with 1 H100115 bolt, an H100004 barrel nut, and an H100031 washer.
Insert hardware to secure the ladder foot bracket inner leg Secure the bracket to the ladder foot with 1 more H100115 bolt, an H100004 barrel nut, and an H100031 washer.
Tighten the ladder foot bracket inner leg Secure the bracket to the ladder foot with 1 more H100115 bolt, an H100004 barrel nut, and an H100031 washer.
Install the chalkboard rails Place the 4 N6 rails along both sides, with the 2 J2 rails inside. Leave 1-1/2 in between rails on the same side.
Insert hardware to secure N6 with 16 screws total Secure the 4 N6 rails from inside with 16 H100088 screws, 2 at the top and 2 at the bottom of each rail.
Secure N6 with 16 screws total Secure the 4 N6 rails from inside with 16 H100088 screws, 2 at the top and 2 at the bottom of each rail.
Insert hardware to secure J2 with 8 screws total Secure the 2 J2 rails from inside with 8 H100121 screws, 2 at the top and 2 at the bottom of each rail.
Secure J2 with 8 screws total Secure the 2 J2 rails from inside with 8 H100121 screws, 2 at the top and 2 at the bottom of each rail.
Place the chalkboard in the middle Place the chalkboard between the side rails over the J2 supports and align its 6 edge holes.
Insert hardware at all 6 mounting holes to secure the chalkboard. Use 6 H100392 screws in the upper, middle, and lower holes on both sides, rather than only at the four corners.
Secure the chalkboard at all 6 mounting holes. Use 6 H100392 screws in the upper, middle, and lower holes on both sides, rather than only at the four corners.
Install the entrance divider post Stand J1 between the ladder and slide, with its upper end against N3. Secure the lower end against the floor with bracket A4M01046.
Insert hardware to secure the post tops Secure the top of J1 to N3 with H100010, a T-nut, and a lock washer.
Secure the post tops Secure the top of J1 to N3 with H100010, a T-nut, and a lock washer.
Insert hardware to secure the post lower corners Secure the vertical leg of the bracket to J1 with H100145, keeping the horizontal leg against the floor.
Secure the post lower corners Secure the vertical leg of the bracket to J1 with H100145, keeping the horizontal leg against the floor.
Insert hardware to secure the post bases Insert H100115 through the bracket and floor, with an H100005 barrel nut and lock washer underneath.
Tighten the post bases Insert H100115 through the bracket and floor, with an H100005 barrel nut and lock washer underneath.
Install the long tower brace Place H6 against the outside of the tower, with its upper end at the floor joist and lower end at the projecting end of M3. Align both sets of holes.
Insert hardware to secure the upper brace end Secure the upper end of H6 to the tower beam with H100649 and an H100138 washer.
Secure the upper brace end Secure the upper end of H6 to the tower beam with H100649 and an H100138 washer.
Insert hardware to secure the lower brace end Secure the lower end of H6 to M3 with H100010, an H100030 washer, and a T-nut.
Secure the lower brace end Secure the lower end of H6 to M3 with H100010, an H100030 washer, and a T-nut.
Install both H5 top rails Connect H5 to the projecting front and rear ends of the two G top rails. Place 4 A4M01110 angle brackets at the inside corners and align the holes.
Insert hardware to secure the top rail ends with 4 screws Drive 4 H100111 screws through each G top rail end into H5, 8 total across both sides.
Secure the top rail ends with 4 screws Drive 4 H100111 screws through each G top rail end into H5, 8 total across both sides.
Insert hardware to secure the angle bracket side Secure the angle bracket to top rail G on each side with 2 H100137 bolts and H100072 T-nuts.
Secure the angle bracket side Secure the angle bracket to top rail G on each side with 2 H100137 bolts and H100072 T-nuts.
Insert hardware to secure the top rail ends with 4 screws Drive 4 H100111 screws through each G top rail end into H5, 8 total across both sides.
Secure the top rail ends with 4 screws Drive 4 H100111 screws through each G top rail end into H5, 8 total across both sides.
Insert hardware to secure the angle bracket side Secure the angle bracket to top rail G on each side with 2 H100137 bolts and H100072 T-nuts.
Secure the angle bracket side Secure the angle bracket to top rail G on each side with 2 H100137 bolts and H100072 T-nuts.
Insert hardware to secure the other angle bracket face Secure the angle brackets to H5 with 2 H100490 bolts per face, H100136 barrel nuts, and H100139 washers.
Secure the other angle bracket face Secure the angle brackets to H5 with 2 H100490 bolts per face, H100136 barrel nuts, and H100139 washers.
Insert hardware to secure the other angle bracket face Secure the angle brackets to H5 with 2 H100490 bolts per face, H100136 barrel nuts, and H100139 washers.
Secure the other angle bracket face Secure the angle brackets to H5 with 2 H100490 bolts per face, H100136 barrel nuts, and H100139 washers.
Install the roof posts Stand the two N4 posts at the centers of the side top rails. Align the lower holes with the angle brackets and keep the tops level.
Insert hardware to secure the post bottoms Secure each N4 to top rail G from the side with 2 H100010 bolts, T-nuts, and H100030 washers.
Secure the post bottoms Secure each N4 to top rail G from the side with 2 H100010 bolts, T-nuts, and H100030 washers.
Insert hardware to secure the post bottoms Secure each N4 to top rail G from the side with 2 H100010 bolts, T-nuts, and H100030 washers.
Secure the post bottoms Secure each N4 to top rail G from the side with 2 H100010 bolts, T-nuts, and H100030 washers.
Install ridge beam N5 Lay N5 across the tops of the two N4 posts. Use 2 A4M01110 angle brackets to connect the ridge beam to the uprights.
Insert hardware at both mounting holes to secure the ridge beam. Secure the ridge beam to the angle brackets with 2 H100141 bolts and H100072 T-nuts.
Secure the ridge beam at both mounting holes. Secure the ridge beam to the angle brackets with 2 H100141 bolts and H100072 T-nuts.
Insert hardware to secure the ridge beam angle brackets Secure the angle bracket to N4 on each side with 1 H100490 bolt, an H100136 barrel nut, and an H100139 washer.
Secure the ridge beam angle brackets Secure the angle bracket to N4 on each side with 1 H100490 bolt, an H100136 barrel nut, and an H100139 washer.
Insert hardware to secure the ridge beam angle brackets Secure the angle bracket to N4 on each side with 1 H100490 bolt, an H100136 barrel nut, and an H100139 washer.
Secure the ridge beam angle brackets Secure the angle bracket to N4 on each side with 1 H100490 bolt, an H100136 barrel nut, and an H100139 washer.
Install both roof braces Place the two H7 braces against the sides of N4, with their lower ends resting on the G top rails.
Insert hardware to secure the roof braces Secure each H7 to N4 with 1 H100649 and an H100138 washer, with the lower end against top rail G.
Tighten the roof braces Secure each H7 to N4 with 1 H100649 and an H100138 washer, with the lower end against top rail G.
Insert hardware to secure the roof braces Secure each H7 to N4 with 1 H100649 and an H100138 washer, with the lower end against top rail G.
Tighten the roof braces Secure each H7 to N4 with 1 H100649 and an H100138 washer, with the lower end against top rail G.
Carry to the tower with two people With two people supporting the beam and A-frame, move through the clear area on the left to the tower, with the L-bracket facing the G1 connection holes.
Insert hardware to secure the tower end of the beam Use 2 H100044 bolts in the upper holes and 2 H100042 bolts in the lower holes, each with a lock washer, flat washer, and T-nut.
Tighten the tower end of the beam Use 2 H100044 bolts in the upper holes and 2 H100042 bolts in the lower holes, each with a lock washer, flat washer, and T-nut.
Insert hardware to secure the tower end of the beam Use 2 H100044 bolts in the upper holes and 2 H100042 bolts in the lower holes, each with a lock washer, flat washer, and T-nut.
Tighten the tower end of the beam Use 2 H100044 bolts in the upper holes and 2 H100042 bolts in the lower holes, each with a lock washer, flat washer, and T-nut.
Drape the canopy over the ridge beam Drape the canopy over ridge beam N5. Fold both canopy edges down against the vertical outer faces of H5 and align the edge holes.
Insert hardware at all 10 mounting holes to secure the canopy. Insert 10 H100070 screws through the canopy edge holes horizontally into the vertical sides of the two H5 rails, 5 per side. Pull the canopy flat.
Secure the canopy at all 10 mounting holes. Insert 10 H100070 screws through the canopy edge holes horizontally into the vertical sides of the two H5 rails, 5 per side. Pull the canopy flat.
Hang one swing assembly Support the swing seat and hook both chain end rings through the quick link openings, using matching links on both sides.
Tighten the quick link locking sleeves Grip each Quick Link threaded sleeve and turn clockwise across the opening until the threads at both ends fully engage.
Tighten the quick link locking sleeves Grip each Quick Link threaded sleeve and turn clockwise across the opening until the threads at both ends fully engage.
Check seat height above ground Use matching chain links on both sides. After all safety installation is complete, have an adult help measure with a person seated. The seat bottom must remain at least 13.8 in (35 cm) above ground.
Hang one swing assembly Support the swing seat and hook both chain end rings through the quick link openings, using matching links on both sides.
Tighten the quick link locking sleeves Grip each Quick Link threaded sleeve and turn clockwise across the opening until the threads at both ends fully engage.
Tighten the quick link locking sleeves Grip each Quick Link threaded sleeve and turn clockwise across the opening until the threads at both ends fully engage.
Check seat height above ground Use matching chain links on both sides. After all safety installation is complete, have an adult help measure with a person seated. The seat bottom must remain at least 13.8 in (35 cm) above ground.
Install both entrance handles Place the handles on left post E2 and center post J1, with the curved grips outward.
Insert hardware to secure the handle upper ends Secure the upper ends of both handles with 2 H100142 bolts, H100138 washers, and H100072 T-nuts.
Secure the handle upper ends Secure the upper ends of both handles with 2 H100142 bolts, H100138 washers, and H100072 T-nuts.
Insert hardware to secure the handle lower ends Fit an H100138 washer on each of 2 H100145 screws and drive into the wood at the lower handle ends. Check that the handles do not wobble.
Secure the handle lower ends Fit an H100138 washer on each of 2 H100145 screws and drive into the wood at the lower handle ends. Check that the handles do not wobble.
Screw in the specified ground stakes Place the stake against E77_0 and screw vertically into the illustrated location until its ring aligns with the wood hole height.
Use the ground stake ring as a drill guide Hold the ground stake ring against the wood. Use a 7/16-inch drill bit through the ring hole to drill through the matching angled leg or ground beam.
Insert hardware to secure the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Tighten the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Screw in the specified ground stakes Place the stake against E77_1 and screw vertically into the illustrated location until its ring aligns with the wood hole height.
Use the ground stake ring as a drill guide Hold the ground stake ring against the wood. Use a 7/16-inch drill bit through the ring hole to drill through the matching angled leg or ground beam.
Insert hardware to secure the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Tighten the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Screw in the specified ground stakes Place the stake against M3 and screw vertically into the illustrated location until its ring aligns with the wood hole height.
Use the ground stake ring as a drill guide Hold the ground stake ring against the wood. Use a 7/16-inch drill bit through the ring hole to drill through the matching angled leg or ground beam.
Insert hardware to secure the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Tighten the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Screw in the specified ground stakes Place the stake against M6 and screw vertically into the illustrated location until its ring aligns with the wood hole height.
Use the ground stake ring as a drill guide Hold the ground stake ring against the wood. Use a 7/16-inch drill bit through the ring hole to drill through the matching angled leg or ground beam.
Insert hardware to secure the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Tighten the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Screw in the specified ground stakes Place the stake against M2 and screw vertically into the illustrated location until its ring aligns with the wood hole height.
Use the ground stake ring as a drill guide Hold the ground stake ring against the wood. Use a 7/16-inch drill bit through the ring hole to drill through the matching angled leg or ground beam.
Insert hardware to secure the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Tighten the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Screw in the specified ground stakes Place the stake against M2 and screw vertically into the illustrated location until its ring aligns with the wood hole height.
Use the ground stake ring as a drill guide Hold the ground stake ring against the wood. Use a 7/16-inch drill bit through the ring hole to drill through the matching angled leg or ground beam.
Insert hardware to secure the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Tighten the ground stake connections Use H100009 with long barrel nuts on angled legs, and H100222 with short barrel nuts on ground beams, each with a lock washer.
Lift the slide to the entrance With two people holding both sides of the slide, lift it around to the outside of the entrance, then lower vertically to mounting height.
Center the slide entrance Rest the slide top at the platform opening, centered left to right. Place the bottom on the ground and the upper slide surface against the floor.
Drill through the slide and floor together Mark as illustrated: holes 7-1/8 in apart, right hole 4-3/8 in from the right edge, and both holes 2 in from the front.
Insert hardware to secure the slide top Insert 2 H100115 bolts downward through the top of the slide and the floor into the H100074 T-nuts underneath.
Tighten the slide top Insert 2 H100115 bolts downward through the top of the slide and the floor into the H100074 T-nuts underneath.
Install the entrance safety rail Place J3 below the canopy and above the ladder and slide entrances, across the outside of the front posts. Align the holes at both ends.
Insert hardware to secure the safety rail with 4 screws Secure J3 with 4 H100111 screws, 2 at each end. Keep the rail firmly seated without wobbling.
Secure the safety rail with 4 screws Secure J3 with 4 H100111 screws, 2 at each end. Keep the rail firmly seated without wobbling.
Install cushioning surfacing after assembly After complete assembly and anchoring, spread bark mulch about 12 in (30 cm) deep initially. Rake level and maintain at least 9 in (23 cm).
Use after adult inspection Check all fasteners, ground anchors, guardrails, and protective surfacing. Use only if no parts are loose or missing.

Inspect and maintain regularly

Retighten hardware regularly Tighten all hardware at the start of the season. Check and tighten twice monthly during the season, and inspect the swing beam and hardware every two weeks.
Check covers and ground anchors At season start and twice monthly during the season, check bolt covers, sharp edges, ground anchors, and protective surfacing. Address missing or damaged items immediately.
Check ropes, chains, and seats monthly At season start and monthly during the season, check hangers, ropes, chains, and seats. Replace worn, rusted, or cracked parts immediately. Lubricate metal moving parts as directed.
Loosen the locking sleeves before cold weather Stop use at season end or below 32°F (0°C). Support the swing seat and unscrew the quick link locking sleeves counterclockwise to expose the openings.
Loosen the locking sleeves before cold weather Stop use at season end or below 32°F (0°C). Support the swing seat and unscrew the quick link locking sleeves counterclockwise to expose the openings.
Remove the plastic swing After opening both quick links, support the swing seat, remove the chain ends through the openings, and store indoors or leave out of use.
Loosen the locking sleeves before cold weather Stop use at season end or below 32°F (0°C). Support the swing seat and unscrew the quick link locking sleeves counterclockwise to expose the openings.
Loosen the locking sleeves before cold weather Stop use at season end or below 32°F (0°C). Support the swing seat and unscrew the quick link locking sleeves counterclockwise to expose the openings.
Remove the plastic swing After opening both quick links, support the swing seat, remove the chain ends through the openings, and store indoors or leave out of use.
Check wood monthly Check wood, slide, and plastic parts monthly. Sand splinters, replace damaged parts, and apply a waterproof sealer annually as directed by the manufacturer.
Rake level and replenish protective surfacing Check protective surfacing twice monthly and at season end. Rake level and replenish bark mulch to at least 9 in (23 cm). Check coverage in all directions.