Loading 3D model
Tap here
Drag to rotate · Right-click or two fingers to pan · Scroll or pinch to zoom · Tap a part for details

All done

FAQ

Stuck?
Start here.

These are the issues buyers run into most when assembling. Tap one to jump to that step in 3D.

All steps

Assemble

  1. Check the parts Check on a rug: A×4, B×4, C×8, D×12, E×16, and wrench F. Assemble with two people.
  2. Position the beam assembly Place the beam with the control box upside down, opening up. Keep both beams parallel and leave space for the brackets.
  3. Connect the left bracket to the beam Move the left bracket above the beam end with its long side running front to back. Lower and align its two center holes with the beam holes.
  4. Insert the left A bolts Insert two type A M6 bolts through the middle of the bracket and give them a few turns by hand.
  5. Tighten the left bracket Tighten both bolts alternately with hex key F until the bracket sits against the beams.
  6. Connect the right bracket to the beam Move the right bracket above the beam end with its long side running front to back. Lower and align its two center holes with the beam holes.
  7. Insert the right A bolts Insert two type A M6 bolts through the middle of the bracket and give them a few turns by hand.
  8. Tighten the right bracket Tighten both bolts alternately with hex key F until the bracket sits against the beams.
  9. Install the left lifting column With two people holding the column, point the motor and mounting tabs downward. Align it with the two beams and lower vertically onto the mounting surface.
  10. Insert the left column D bolts Insert four D bolts through the column mounting tabs into the front and rear beams. Start all by hand.
  11. Tighten the left upright Tighten the four D bolts diagonally with hex key F until the mounting tabs sit against the beams.
  12. Install the right lifting column With two people holding the column, point the motor and mounting tabs downward. Align it with the two beams and lower vertically onto the mounting surface.
  13. Insert the right column D bolts Insert four D bolts through the column mounting tabs into the front and rear beams. Start all by hand.
  14. Tighten the right upright Tighten the four D bolts diagonally with hex key F until the mounting tabs sit against the beams.
  15. Install the left foot base Orient the long foot base front to back, leveling feet up. Lift over the column end, then lower vertically and align the four center holes.
  16. Insert the left C bolts Insert four C bolts from beneath the foot base into the column holes. Start all by hand.
  17. Tighten the left foot base Tighten the four bolts diagonally with hex key F until the foot base sits against the column.
  18. Install the right foot base Orient the long foot base front to back, leveling feet up. Lift over the column end, then lower vertically and align the four center holes.
  19. Insert the right C bolts Insert four C bolts from beneath the foot base into the column holes. Start all by hand.
  20. Tighten the right foot base Tighten the four bolts diagonally with hex key F until the foot base sits against the column.
  21. Lift the desk frame With two people holding both sides of the frame, lift it while keeping it upside down to make room for the desktop underneath.
  22. Desktop face down Place the desktop face down on soft padding, then slowly lower the upside-down frame onto its underside, centered front to back.
  23. Loosen the width locking screws Loosen the four pre-installed telescoping screws with wrench F just enough for the beams to slide. Leave in the holes.
  24. Adjust width to the desktop Pull the beams outward to match the actual desktop size and center them left to right. Keep sufficient overlap at both end connections.
  25. Retighten the beams Tighten the four telescoping screws one by one with wrench F until neither side slides when pushed or pulled.
  26. Insert the left bracket screws Place one E screw in each of the four front and rear holes of the left bracket, four total. Align with the desktop underside mounting points.
  27. Secure the left bracket Tighten each with a Phillips screwdriver. Stop when the screw heads meet the steel plate; do not strip the threads.
  28. Insert the right bracket screws Place one E screw in each of the four front and rear holes of the right bracket, four total. Align with the desktop underside mounting points.
  29. Secure the right bracket Tighten each with a Phillips screwdriver. Stop when the screw heads meet the steel plate; do not strip the threads.
  30. Insert the beam connector plate screws Place one E screw in each of the four holes in the center beam plate, four total. Align with the desktop underside mounting points.
  31. Secure the beam connector plate Tighten each with a Phillips screwdriver. Stop when the screw heads meet the steel plate; do not strip the threads.
  32. Position the handset Place the handset mounting tabs against the underside of the desktop front edge, buttons outward. Align both holes with the mounting points.
  33. Insert the handset screws Insert two E screws through the handset mounting tabs and hand-tighten.
  34. Secure the handset Tighten both screws with a Phillips screwdriver until the handset mounting tabs sit flat without wobbling.
  35. Connect the left motor to M1 Align the left column motor plug with control box M1 and push along the socket axis until the housings meet.
  36. Connect the right motor to M2 Align the right column motor plug with M2 and push fully along the socket axis. Do not twist forcefully.
  37. Connect the handset cable to HS Align the handset harness wide plug with HS and push fully along the socket axis.
  38. Connect the branch cable to DC Connect the round plug on the same handset harness to DC, pushing fully along the socket axis. Do not connect the AC power cord yet.
  39. Connect the power cord to AC Insert connecting cable ⑧ into the AC port at the other control box end until the housings meet. Leave the wall end disconnected for now.
  40. Start the four B screws Start the four B screws in the beam mounting holes with wrench F. Give them just a few turns, leaving room to engage the cover.
  41. Hook one side of the cover on first Tuck cables away, then lift and tilt the cover slightly so one side's open slots slide beneath the two B screw shanks.
  42. Press in the other side of the cover Press down the raised cover edge until the other two open slots engage beneath the B screw shanks. Do not release until all four points engage.
  43. Tighten the cable cover Tighten the four B screws one by one with hex key F until the cover sits against the beams and neither side can come loose.
  44. Turn the desk upright with two people Confirm all screws are tight and cables unpinched. With two people holding the frame and desktop, lift off the floor, turn upright, and set securely.
  45. Connect AC power Once the desk is stable, insert the power plug fully. Use 100–240 V, 50/60 Hz power.
  46. Reset when ASr appears If ASr appears after powering on, press and hold ▼ until the desk lowers fully, rebounds, and stops, then release.

Height memory and handset

  1. Set to sitting height Hold ▲ until the desktop is level with your elbows when seated. Let go to stop.
  2. Save as 1 Press M once. When the display flashes S-, press 1. The sitting height is saved.
  3. Raise to standing height Hold ▲ until your elbows bend about 90° when typing while standing.
  4. Save as 2 Press M, then 2. The standing height is saved too.
  5. Try one-touch switching Press 1 to return to sitting height, then 2 to return to standing height.
  6. Save the standing height preset At the desired height, press M, then the standing icon button. S-3 appears and the current height is saved to that button.
  7. Hold to lower; release to stop Press and hold ▼ to lower the desktop. Release at sitting height. The display shows the current height.
  8. Save the sitting height preset Press M, then the sitting icon button. S-4 appears and the current height is saved to that button.
  9. Recall standing and sitting presets Press the standing icon button to return automatically to position 3, then the sitting icon button to return to position 4.
  10. Press and hold M to enable the child lock Press and hold M for about 5 seconds. Release when the blue light above ▼ and M turns on. Child lock is enabled and the buttons cannot adjust height.
  11. Press and hold M to disable the child lock Press and hold M again for about 5 seconds. Release when the child lock turns off; the buttons return to normal use.
  12. Optional anti-collision settings Press and hold ▲ and ▼ together for 5 seconds to change sensitivity: A-3 high, A-2 medium, A-1 low, A-0 off.

Cable routing for a wide frame

  1. Confirm wide frame requirements Above 67.7 in frame width, center the cable cover on the beams. This task starts with the desktop secured and wiring connected.
  2. Install the wide frame D bolts Start the four D bolts in the outer beam stop holes specified for method 2. Do not tighten yet.
  3. Start the four B screws Start the four B screws in the beam mounting holes with wrench F. Give them just a few turns, leaving room to engage the cover.
  4. Hook one side of the cover on first Tuck cables away, then lift and tilt the cover slightly so one side's open slots slide beneath the two B screw shanks.
  5. Press in the other side of the cover Press down the raised cover edge until the other two open slots engage beneath the B screw shanks. Do not release until all four points engage.
  6. Tighten the cable cover Tighten the four B screws one by one with hex key F until the cover sits against the beams and neither side can come loose.
  7. Tighten the wide frame D bolts Tighten all four D bolts with hex key F. Check that the telescoping bars do not extend beyond the stop holes.