Loading 3D model
Tap here
Drag to rotate · Right-click or two fingers to pan · Scroll or pinch to zoom · Tap a part for details

All done

FAQ

Stuck?
Start here.

These are the issues buyers run into most when assembling. Tap one to jump to that step in 3D.

All steps

Assemble the stroller

  1. Check the parts Lay protective cardboard. Check the frame, seat, canopy, rear axle, two each of front wheels, rear wheels, and brake housings, both trays, mounts, and red bag hardware.
  2. Remove shipping ties If the frame has shipping ties, remove and discard them immediately.
  3. Flip open the fold latch Pull the left fold latch outward off the frame to release the storage lock.
  4. Unfold the frame upward Lift the handle until both side hinges lock. Confirm the frame is fully unfolded before installing other parts.
  5. Place the frame upside down Support the frame and lay it backward with the handle securely on protective cardboard, exposing the rear leg ends and wheel sockets.
  6. Attach the left brake housing Face the left brake housing pedal rearward. Push fully onto the left rear leg end until it clicks.
  7. Attach the right brake housing Face the right brake housing pedal rearward. Push fully onto the right rear leg end until it clicks.
  8. Insert the separate rear axle Insert the rear axle from the left through both brake housing cross-holes. Leave equal lengths exposed at both ends, with the pin holes outside the wheels.
  9. Slide on the left rear wheel Align the left rear wheel hub hole with the axle and push fully inward from outside, exposing the small axle end hole.
  10. Slide on the right rear wheel Align the right rear wheel hub hole with the axle and push fully inward from outside, exposing the small axle end hole.
  11. Insert the left wheel cotter pin Align the straight leg of the left cotter pin with the axle hole and push completely through. The curved leg wraps around the rear axle, with the bent end outward.
  12. Insert the right wheel cotter pin Align the straight leg of the right cotter pin with the axle hole and push completely through. The curved leg wraps around the rear axle, with the bent end outward.
  13. Fit the left hub cap Align the left hub cap with the wheel center and press inward from outside until latched, covering the cotter pin.
  14. Pull the left rear wheel to check Pull the left rear wheel outward. It must not come off the axle, and the cotter pin and hub cap must stay in place.
  15. Fit the right hub cap Align the right hub cap with the wheel center and press inward from outside until latched, covering the cotter pin.
  16. Pull the right rear wheel to check Pull the right rear wheel outward. It must not come off the axle, and the cotter pin and hub cap must stay in place.
  17. Attach the left front wheel Align the left front wheel stem with that side's front leg socket. Push along the hole axis until it clicks.
  18. Pull the left front wheel to check Pull the left front wheel assembly opposite the stem insertion direction. It is locked only if it cannot come out.
  19. Attach the right front wheel Align the right front wheel stem with that side's front leg socket. Push along the hole axis until it clicks.
  20. Pull the right front wheel to check Pull the right front wheel assembly opposite the stem insertion direction. It is locked only if it cannot come out.
  21. Raise the frame Hold the frame with both hands and slowly turn right side up onto all four wheels.
  22. Attach the parent tray Keep the parent tray cup wells up. Align both ends with the mounts below the handle and press down until both sides latch.
  23. Attach the left seat mount Align the left seat mount with the frame socket on that side. Press down until locked, then pull up to confirm it cannot come out.
  24. Attach the right seat mount Align the right seat mount with the frame socket on that side. Press down until locked, then pull up to confirm it cannot come out.
  25. Turn the seat over and set securely Grip both seat sides, lift, turn over, and set upside down on protective cardboard.
  26. Insert the upper frame tubes Align both upper frame tubes with the tube openings on the seat sides. Push fully along the tube axes and check that both spring tabs engage.
  27. Fasten the left fabric sleeve Wrap the left fabric flap around the upper frame tube. Fasten the first snap set, then the second. Check both sets are secure and the fabric sleeve cannot slip off.
  28. Fasten the right fabric sleeve Wrap the right fabric flap around the upper frame tube. Fasten the first snap set, then the second. Check both sets are secure and the fabric sleeve cannot slip off.
  29. Flip the steel wire up Keep the seat upside down. Flip the movable underside wire up to a position where the fabric flap can wrap around it.
  30. Wrap the fabric flap around the steel wire Fold the underside fabric flap over the seat wire, wrap around the crossbar, and align all three snaps.
  31. Fasten bottom snap 1 Press and hold this bottom snap until both halves fasten. Gently pull the fabric to check it stays fastened.
  32. Fasten bottom snap 2 Press and hold this bottom snap until both halves fasten. Gently pull the fabric to check it stays fastened.
  33. Fasten bottom snap 3 Press and hold this bottom snap until both halves fasten. Gently pull the fabric to check it stays fastened.
  34. Align the canopy frame with its mounts Keep the seat upside down. Align the canopy frame ends with the dedicated canopy sockets on both sides.
  35. Insert both canopy frame ends securely Push both canopy frame ends together into the canopy sockets until both sides latch.
  36. Attach the left elastic loop Stretch the left canopy elastic loop over that side's small hook and check that it cannot slip off.
  37. Attach the right elastic loop Stretch the right canopy elastic loop over that side's small hook and check that it cannot slip off.
  38. Fasten the left hook-and-loop strap Wrap the left canopy tab down and fasten its hook-and-loop strip snugly.
  39. Fasten the right hook-and-loop strap Wrap the right canopy tab down and fasten its hook-and-loop strip snugly.
  40. Turn the seat right side up Support both seat sides with your hands. Lift, turn right side up, and set securely. Do not lift the seat by its footrest.
  41. Align the seat with the mounts Support the empty seat facing forward above the frame. Align both attachment points with the two seat mounts.
  42. Press in and check the seat Press the seat down until both sides lock, then pull up. Neither side may detach from the mounts.
  43. Attach the child tray Align both end posts with the seat armrest sockets. Press straight down until both sides latch.
  44. Open the canopy Pull the canopy front edge toward the stroller front until all sections unfold around the canopy pivot.

Attach the carrier and fold

  1. Lock the brakes first Remove the child first. Press both rear brake pedals down and gently push the frame to confirm it cannot roll.
  2. Press and hold both side release buttons Squeeze both seat side release buttons inward with both hands and keep holding them while lifting straight off the mounts.
  3. Set the seat aside Lift the seat above its mounts, move sideways into the clear area on the left, then lower onto protective cardboard.
  4. Confirm carrier compatibility Confirm the carrier is a Graco SnugRide marked Click Connect. Read its manual before installing.
  5. Line up the carrier with the mounts Support the carrier above the frame and align both sockets with the seat mounts. Install rear-facing in this step.
  6. Press until both sides lock Lower the carrier vertically and press down until both side latches engage the seat mounts.
  7. Pull the carrier up to check Grip the handle and pull straight up. Use only if neither side detaches from the mounts.
  8. Squeeze the release handle Squeeze the release handle behind the carrier head end inward toward the shell and keep holding to unlock.
  9. Keep squeezing and lift Keep squeezing the release handle while lifting the carrier with the other hand. Release only after the sockets clear the mounts completely.
  10. Set the carrier aside Support and lift the carrier, move to the right, then lower vertically onto its separate base.
  11. Reattach the seat facing forward Support the empty seat and reinstall forward-facing with its backrest upright. Once both sides latch, pull up to check.
  12. Pull up both fold latches Grip the fold latches on both sides of the handle and pull upward along the handle until unlocked.
  13. Push the handle down to fold the stroller Keep unlocked, then push the handle forward and down, slowly bringing the frame into the folded position.
  14. Check the storage latch Confirm that the side storage latch hooks onto the frame and that a gentle pull on the handle does not unfold it. Then stand the stroller upright, resting on its rear wheels and handle.