Loading 3D model
Tap here
Drag to rotate · Right-click or two fingers to pan · Scroll or pinch to zoom · Tap a part for details

All done

FAQ

Stuck?
Start here.

These are the issues buyers run into most when assembling. Tap one to jump to that step in 3D.

All steps

Open the play yard

  1. Check the supplied parts Check the frame, original four-section mattress, and carry bag. Accessories include the bassinet, 6 tubes, 8 pre-installed clips, toy bar, and storage bag.
  2. Unzip the carry bag Grip the zipper pull and unzip fully along the carry bag side seam to the other end.
  3. Remove the carry bag Lift the open carry bag vertically above the frame, then move outside and lower.
  4. Unfasten the transport straps Unfasten both transport straps holding the mattress around the frame before removing the mattress.
  5. Remove the mattress Lift the mattress off the outside of the folded frame, move it over the frame and aside, then unfold its four sections and lay flat.
  6. Pull the four corners apart Place all four feet down on level ground. Pull the corners outward, keeping the floor center raised.
  7. Pull up the front top rail Grip the front top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  8. Pull up the rear top rail Grip the rear top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  9. Pull up the left top rail Grip the left top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  10. Pull up the right top rail Grip the right top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  11. Check all four top rails Check each rail has both sections locked straight and is rigid. If unlocked, lift again. Raise the center first if too low.
  12. Check the corner fabric covers Check each top corner to confirm the fabric covers the fittings without lifting or exposing them.
  13. Press down the center of the floor Lift one end of the bed with one hand and press the floor center down with the other until locked and completely flat.
  14. Lay in the mattress Lift the original mattress above the top rail, then over the bed interior. Lower straight to the floor with its soft side up and spread flat.
  15. Fasten the left front strap Pass the mattress left front strap through the floor fabric corner gap, wrap around the bottom tube, and fasten the snap securely.
  16. Fasten the left rear strap Pass the mattress left rear strap through the floor fabric corner gap, wrap around the bottom tube, and fasten the snap securely.
  17. Fasten the right front strap Pass the mattress right front strap through the floor fabric corner gap, wrap around the bottom tube, and fasten the snap securely.
  18. Fasten the right rear strap Pass the mattress right rear strap through the floor fabric corner gap, wrap around the bottom tube, and fasten the snap securely.
  19. Check before use Before placing the child inside, confirm all four rails are locked straight, the floor locked flat, the mattress smooth, and all four corner straps fastened.

Fold the standard play yard

  1. Unfasten the left front strap Reach under the bed, open the left front snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  2. Unfasten the left rear strap Reach under the bed, open the left rear snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  3. Unfasten the right front strap Reach under the bed, open the right front snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  4. Unfasten the right rear strap Reach under the bed, open the right rear snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  5. Remove the mattress completely After unfastening all four corner straps, lift the mattress vertically over the top rails, then move outside the bed and set down.
  6. Lift the floor strap Pull the red floor strap up until it unlocks and the center rises at least halfway. Do not unlock the top rails yet.
  7. If stuck, raise the center further If top rails will not release, stop forcing them. Raise the red floor strap further, then press each rail button to release both sections.
  8. Unlock the right top rail Lift the right top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  9. Unlock the left top rail Lift the left top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  10. Unlock the rear top rail Lift the rear top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  11. Unlock the front top rail Lift the front top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  12. Bring the four corners together Confirm both sections of all four top rails are released, then gather the corners into a bundle. Stop immediately if resistance occurs.
  13. Roll the mattress outside the bed Fold the four mattress sections into four sides along the creases, soft side inward. Do not fasten the transport straps yet.
  14. Wrap the mattress around the frame Lift the wrapped mattress over the frame to directly above it, then lower around the folded frame.
  15. Fasten the transport straps Wrap the two exterior mattress transport straps around the opening snugly. Check that the mattress holds the frame without coming apart.
  16. Pack in the carry bag Lift the empty carry bag above the folded frame and slide fully down over it. Keep the exterior mattress handle through the opening.
  17. Zip the carry bag closed Check that the handle extends through the opening. Pull the zipper fully along the side seam to close the carry bag.

Install the bassinet

  1. Unfasten the left front strap Reach under the bed, open the left front snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  2. Unfasten the left rear strap Reach under the bed, open the left rear snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  3. Unfasten the right front strap Reach under the bed, open the right front snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  4. Unfasten the right rear strap Reach under the bed, open the right rear snap, unwrap the strap from the bottom tube, and feed it back through the floor fabric corner gap.
  5. Remove the floor mattress Unfasten the four corner snap straps under the floor and remove the original mattress completely. The same mattress will go into the bassinet later.
  6. Lower into the bassinet from above Unfold the bassinet, lift over the top rails, move directly above the play yard, and lower inside. Align all 8 clips with the top rails first.
  7. Fasten clip 1 Align the bassinet front left clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  8. Fasten clip 2 Align the bassinet front right clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  9. Fasten clip 3 Align the bassinet rear left clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  10. Fasten clip 4 Align the bassinet rear right clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  11. Fasten clip 5 Align the bassinet left rear clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  12. Fasten clip 6 Align the bassinet left front clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  13. Fasten clip 7 Align the bassinet right rear clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  14. Fasten clip 8 Align the bassinet right front clip with the top rail. Press down until latched, then check that the clip wraps around the rail.
  15. Connect the rear set left end securely Align the reduced end of the rear left side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  16. Connect the rear set right end securely Align the reduced end of the rear right side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  17. Connect the front set left end securely Align the reduced end of the front left side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  18. Connect the front set right end securely Align the reduced end of the front right side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  19. Place the mattress in the bassinet Confirm all 8 clips and both support tube sets are secure, then lower the original mattress vertically into the bassinet, soft side up, and lay flat.

Fold with the bassinet attached

  1. Remove the bassinet mattress Lift the mattress vertically out of the bassinet over the top rails, move outside, and lower. Keep all 8 bassinet clips attached.
  2. Disconnect the rear set left end Grip the rear left side tube and pull its reduced end outward along the axis, then separate the inner end upward. Keep the tube in the bassinet fabric sleeve.
  3. Disconnect the rear set right end Grip the rear right side tube and pull its reduced end outward along the axis, then separate the inner end upward. Keep the tube in the bassinet fabric sleeve.
  4. Disconnect the front set left end Grip the front left side tube and pull its reduced end outward along the axis, then separate the inner end upward. Keep the tube in the bassinet fabric sleeve.
  5. Disconnect the front set right end Grip the front right side tube and pull its reduced end outward along the axis, then separate the inner end upward. Keep the tube in the bassinet fabric sleeve.
  6. Lift the floor strap Reach through the opening beneath the bassinet and pull up the red strap at the play yard floor center. Raise the center at least halfway.
  7. If stuck, raise the center further If top rails will not release, stop forcing them. Raise the red floor strap further, then press each rail button to release both sections.
  8. Unlock the right top rail Lift the right top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  9. Unlock the left top rail Lift the left top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  10. Unlock the rear top rail Lift the rear top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  11. Unlock the front top rail Lift the front top rail midpoint slightly, press and hold the side button inward, then fold down. Confirm both tube sections release.
  12. Bring the four corners together Confirm both sections of all four top rails are released, then gather the corners into a bundle. Stop immediately if resistance occurs.
  13. Roll the mattress outside the bed Fold the four mattress sections into four sides along the creases, soft side inward. Do not fasten the transport straps yet.
  14. Wrap the mattress around the frame Lift the wrapped mattress over the frame to directly above it, then lower around the folded frame.
  15. Fasten the transport straps Wrap the two exterior mattress transport straps around the opening snugly. Check that the mattress holds the frame without coming apart.
  16. Pack in the carry bag Lift the empty carry bag above the folded frame and slide fully down over it. Keep the exterior mattress handle through the opening.
  17. Zip the carry bag closed Check that the handle extends through the opening. Pull the zipper fully along the side seam to close the carry bag.

Unfold with the bassinet attached

  1. Unzip the carry bag Grip the zipper pull and unzip fully along the carry bag side seam to the other end.
  2. Remove the carry bag Lift the open carry bag vertically above the frame, then move outside and lower.
  3. Unfasten the transport straps Unfasten both transport straps holding the mattress around the frame before removing the mattress.
  4. Remove the mattress Lift the mattress off the outside of the folded frame, move it over the frame and aside, then unfold its four sections and lay flat.
  5. Pull the frame open with the bassinet attached Set all four feet securely down and pull the corners outward. Keep the bassinet clipped to the top rails and the support tubes disconnected for now.
  6. Pull up the front top rail Grip the front top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  7. Pull up the rear top rail Grip the rear top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  8. Pull up the left top rail Grip the left top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  9. Pull up the right top rail Grip the right top rail midpoint above the button and lift until both tube sections lock straight and the rail is rigid.
  10. Check all four top rails Check each rail has both sections locked straight and is rigid. If unlocked, lift again. Raise the center first if too low.
  11. Check the corner fabric covers Check each top corner to confirm the fabric covers the fittings without lifting or exposing them.
  12. Press down the center of the floor Lift one end of the bed with one hand. Reach through the opening under the bassinet with the other and press the play yard center down until locked.
  13. Check all eight clips Check around all four bassinet sides to confirm all 8 clips remain fully secured to the top rails, with none loose or missed.
  14. Connect the rear set left end securely Align the reduced end of the rear left side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  15. Connect the rear set right end securely Align the reduced end of the rear right side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  16. Connect the front set left end securely Align the reduced end of the front left side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  17. Connect the front set right end securely Align the reduced end of the front right side tube with the center tube opening and insert fully along the axis. The joint must be secure and must not come apart.
  18. Place the mattress in the bassinet Confirm all 8 clips and both support tube sets are secure, then lower the original mattress vertically into the bassinet, soft side up, and lay flat.

Assemble the toy bar

  1. Connect the first rod to the center connector Outside the bed, align the first plastic rod's narrow center end with the center connector opening and insert securely along the axis.
  2. Feed the bars through the fabric sleeve Insert the connected bars into the toy bar fabric sleeve and smooth the sleeve along the bars.
  3. Insert the other rod Insert the other plastic rod through the fabric sleeve and align it with the center connector.
  4. Connect the other end securely Connect the other rod to the center connector. Check that both rods are securely connected, then smooth the fabric sleeve.
  5. Attach the supplied toys Secure the supplied toy straps to the sleeve attachment points. Check that they are secure and keep toys away from the baby's face and mouth.
  6. Move the toy bar above Hold the complete toy bar, lift, then move above the play yard. Align the end mounts with the front and rear top rails.
  7. Press the first end mount firmly on Press the first end mount down onto the rear top rail and check that its jaws engage. Keep the other end raised for now.
  8. Press the other end mount firmly on Keep the first end clipped on. Pivot the other end down around it and press onto the front top rail. Secure both ends.

Install the exterior storage bag

  1. Keep the storage bag outside Move the storage bag outside the short side. Align both ends with the exterior attachment points, opening up, keeping the entire bag outside the bed.
  2. Secure both ends of the storage bag Secure both storage bag ends to the exterior attachment points on the short side. Check each connection is secure and keep the bag outside the bed.

Remove the attachment

  1. Remove the toy bar Hold the toy bar end mounts and lift off the top rails. Lift it with the toys over the bed edge, then move outside and lower.
  2. Remove the storage bag Support the exterior storage bag and disconnect both ends. Then move it away from the bed and lower it.