Loading 3D model
Tap here
Drag to rotate · Right-click or two fingers to pan · Scroll or pinch to zoom · Tap a part for details

All done

FAQ

Stuck?
Start here.

These are the issues buyers run into most when assembling. Tap one to jump to that step in 3D.

All steps

Install the bowl and beater

  1. Return the speed lever to zero Lift the left speed lever slightly, move back to 0, then release down.
  2. Unplug the power cord Grip the plug body and pull straight out of the wall outlet.
  3. Slide the lever to unlock Slide the right locking lever forward to unlock.
  4. Raise the head Support the motor head, raise backward to the stop, and keep it raised.
  5. Align with the bowl base Lift the bowl, move directly above the clamping plate, then lower with the bowl bottom aligned.
  6. Lock the bowl clockwise Viewed from above the bowl, hold the handle and turn gently clockwise until locked.
  7. Align with the shaft cross pin Lift the flat beater from the front and align its sleeve opening with the beater shaft cross pin.
  8. Push fully along the axis Push the flat beater fully up the beater shaft to the stop.
  9. Turn counterclockwise to hang in place Viewed down the shaft from the motor head, turn the attachment counterclockwise, then release it onto the cross pin.
  10. Lower the motor head completely Support the motor head and lower slowly all the way down.
  11. Lock and try lifting With the motor head fully down, slide the lever back to Lock. Try lifting; it is secure only if it cannot rise.
  12. Install the cover from the front If supplied, slide the pouring shield in from directly in front and center it, with the lower edge inside the bowl rim and the feed chute on the right.

Adjust the beater clearance

  1. Stop to prepare for adjustment Adjust only if the beater scrapes the bowl or misses ingredients at the bottom. Lift the speed lever slightly and return it to 0.
  2. Unplug first Grip the plug and unplug from the wall before approaching the beater.
  3. Unlock and raise the motor head Slide the lever to Unlock and support the head as you raise it to the stop, exposing the screw on top of the column.
  4. Insert the tip into the slot Approach from the front and above with a flathead screwdriver. Insert the tip into the slot, keeping the handle clear of the raised motor head.
  5. Adjust the screw slightly Viewed from above the screw, a small counterclockwise turn raises the beater; a small clockwise turn lowers it.
  6. Withdraw the screwdriver Withdraw the tip along the entry path, then move the tool outside the head, clear of its lowering path.
  7. Lower the head to check clearance Support and lower the motor head fully. The flat beater should just clear the bowl bottom and sides.
  8. Relock and try lifting Slide the locking lever back and try lifting to confirm the head cannot rise. If it will not lock, unplug and readjust slightly.
  9. Plug in and check at low speed Confirm speed 0 and a locked motor head before plugging in. Test briefly at the lowest speed. Stop and unplug immediately if scraping occurs.

Choose speeds and clean up

  1. Check locking before running Before each run, confirm the head is fully lowered and lever at Lock. Try lifting to verify.
  2. Plug into a grounded wall outlet Keep the speed lever at 0 and insert the three-prong plug fully into a grounded three-prong wall outlet.
  3. Start at the lowest speed Lift the speed lever slightly to Stir and increase gradually. After combining dry ingredients, select the recipe speed.
  4. Stop, then unplug Lift the speed lever slightly to 0, wait for the attachment to stop, then grip the plug and unplug.
  5. Unlock and raise the head Slide the locking lever forward to Unlock and support the head as you raise it to the stop.
  6. Remove the pouring shield first If fitted, lift the shield front edge clear of the bowl rim, pull forward off, and place on the counter.
  7. Remove the flat beater Push up the shaft. Viewed down the shaft from the motor head, turn clockwise, then pull down off the shaft and place on the counter.
  8. Install the dough hook Align the dough hook sleeve with the cross pin and push fully up. Viewed down the shaft from the head, turn counterclockwise, then release onto the pin.
  9. Lower the head for kneading Support and lower the motor head fully with the attachment inside the bowl.
  10. Lock before kneading Slide the locking lever back. Try lifting the motor head to confirm it cannot rise.
  11. For dough, use speed 2 only. Plug in, lift the speed lever slightly, and move to 2. Use the dough hook at speed 2 for both mixing and kneading yeast dough.
  12. Stop to prepare for changing attachments Return the speed lever to 0, wait for the dough hook to stop, then unplug.
  13. Unlock and raise the motor head Slide the locking lever forward to Unlock and support the head as you raise it to the stop.
  14. Remove the dough hook Push up the shaft. Viewed down the shaft from the motor head, turn clockwise, then pull off along the shaft and set securely on the counter.
  15. Install the wire whip Align the wire whip with the cross pin and push fully up. Viewed down the shaft from the motor head, turn counterclockwise, then release onto the cross pin.
  16. Lower the head Support the motor head and lower slowly all the way down.
  17. Lock before whipping Slide the lever back to lock the motor head. Try lifting to confirm it cannot rise.
  18. Increase gradually to speed eight Plug in and start at Stir, increasing through speeds 2, 4, 6, and 8. Suitable for two or more egg whites or larger amounts of cream.
  19. Use speed 10 for small amounts For one egg white or less than 6.8 fl oz (200 mL) of cream, gradually increase to speed 10. Watch the consistency to avoid overwhipping.
  20. Stop and unplug Return the speed lever to 0, wait for the wire whip to stop, then unplug.
  21. Unlock and raise the head to remove attachments Slide the locking lever forward to Unlock and support the head as you raise it backward.
  22. Remove the wire whip Push up, then turn clockwise. Pull down along the shaft, move forward clear of the machine, and set securely.
  23. Remove the bowl counterclockwise Viewed from above the bowl, turn counterclockwise to loosen. Lift vertically clear of the clamping plate, then move out and set securely.
  24. Wipe the body with a damp cloth Keep unplugged. Wipe the body with a soft damp cloth. Do not use household or commercial cleaners.
  25. Wipe the beater shaft clean Keep unplugged. Wipe residue off the beater shaft with a damp cloth. Do not store attachments on the shaft after cleaning.
  26. Wash the bowl and coated attachments The bowl, shield, flat beater, and white dough hook are dishwasher-safe or can be hand-washed with hot soapy water. Rinse and air-dry.
  27. Wash the wire whip by hand only. Hand-wash the wire whip with hot soapy water, rinse thoroughly, air-dry, and store off the mixer.

Install the optional attachment

  1. Return the speed lever to zero Before installing an attachment, lift the speed lever slightly, return to 0, and release.
  2. Confirm the plug is removed Confirm the plug is removed from the wall before installing an attachment.
  3. Loosen the locking knob Viewed from above the knob, loosen the locking knob at the front of the motor head counterclockwise.
  4. Remove the attachment hub cover Grip the hub cover, pull straight forward off, and place on the counter.
  5. Align and insert the attachment Align the attachment's square shaft with the square hub hole and insert fully backward. Gently rotate back and forth if needed to seat the locating pin in the notch.
  6. Tighten clockwise Viewed from above the knob, tighten clockwise until the attachment is secure. See its separate manual for use.

Switch to the optional flex edge beater

  1. Stop to prepare for changing attachments Lift the speed lever slightly to 0 and wait for the attachment to stop.
  2. Unplug first Grip the plug body and unplug from the wall outlet.
  3. Unlock and raise the motor head Slide the locking lever forward to Unlock and support the head as you raise it to the stop.
  4. Remove the flat beater Push up, turn clockwise, and pull off along the shaft, then move it forward onto the counter.
  5. Install the flex edge beater Align the optional flex edge beater with the cross pin and push fully up. Viewed down the shaft from the head, turn counterclockwise and release onto the pin.
  6. Lower the motor head completely Support the motor head and lower fully, with the flex edge beater inside the bowl.
  7. Lock and try lifting Slide the lever back to lock the motor head. Try lifting to confirm it cannot rise.