Loading 3D model
Tap here
Drag to rotate · Right-click or two fingers to pan · Scroll or pinch to zoom · Tap a part for details

All done

FAQ

Stuck?
Start here.

These are the issues buyers run into most when assembling. Tap one to jump to that step in 3D.

All steps

Place the auto-empty dock and power on

  1. Unbox and check parts Unpack the robot, auto-empty dock, power cord, moisture-proof mat, mop bracket, and mop cloth. Check that all packaging is removed.
  2. Clear the floor Put away cords, sharp objects, and breakables. Install physical barriers at raised edges and stairs.
  3. Place the dock with its back to the wall Place the auto-empty dock against a wall on a flat, hard floor, away from direct sunlight and heat.
  4. Measure the clearance Leave at least 1.64 ft (0.5 m) on each side of the dock and 4.92 ft (1.5 m) in front. Choose a location with good WiFi.
  5. Connect and tuck away the cables Connect the power cord to the dock. Tuck excess into the rear channel and route out either side.
  6. Connect power Plug into the wall outlet and confirm the dock status light turns white.
  7. Lay the moisture-proof mat Wipe the floor clean with a dry cloth. Peel the mat backing, place the mat in front of the dock, and press flat.
  8. Peel off the front protective film Pinch a corner of the front locator protective film and peel outward to expose the locator.
  9. Peel off the rear protective film Peel the protective film off the rear locator from a corner outward.
  10. Hold to power on Press and hold Power until the robot power light turns steady white, then release.
  11. Place on the dock to charge Place the robot on the dock with its charging contacts touching. Confirm the robot power light pulses.
  12. Vacuuming run 1 Leave the mop bracket off. Press the power button while on the dock to start vacuuming, then wait for automatic docking when finished.
  13. Vacuuming run 2 Leave the mop bracket off. Press the power button while on the dock to start vacuuming, then wait for automatic docking when finished.
  14. Vacuuming run 3 Leave the mop bracket off. Press the power button while on the dock to start vacuuming, then wait for automatic docking when finished.
  15. Remove from the dock and set securely Move the robot off the dock and place upright on a flat floor, leaving room behind to remove the module.
  16. Press the button to remove the combined module Press and hold the module release button, then pull the combined dustbin/water tank outward, supporting underneath.
  17. Open the water tank plug Hold the module with one hand and open the water tank plug with the other to expose the fill opening.
  18. Add cold tap water Add cold tap water through the fill opening, keeping the dustbin and filter dry.
  19. Close the water tank plug securely Press the water tank plug back into the fill opening and firmly around its edges. Check that it seals.
  20. Wet and wring out the mop cloth Wet the mop cloth with water and wring out until not dripping before installing.
  21. Attach the mop cloth flat Attach the mop cloth underneath the bracket. Spread and press flat without curled edges.
  22. Align with the module underside Support the combined module. Align the mop bracket locating holes with the module underside and install fully.
  23. Reinstall the combined module Support the combined module with its mop bracket attached and reinstall in the robot. Check that it locks.

Connect the app and create the first map

  1. Download the app Search for Roborock in your app store, download it, and follow the prompts to log in.
  2. Reset WiFi With the robot on, press and hold the power and dock buttons together for 3 seconds. Release after the WiFi setup prompt.
  3. Add device In the app, tap "Add device" or "+" and follow the prompts to connect to your home 2.4 GHz WiFi.
  4. Start cleaning Once the module is installed, press the robot's power button while it is on the dock to start cleaning. The robot cleans along the edges first, then follows an S-shaped path.
  5. Auto-empties on return to the dock After cleaning, wait for automatic docking, emptying, and charging.

Routine maintenance

  1. Remove from the dock and set securely Move the robot off the dock and set upright on a flat floor, ready to power off.
  2. Press and hold to power off Press and hold Power until the indicator goes out, then release before maintenance.
  3. Unplug the dock Grip the plug and pull out of the wall outlet. Confirm the dock is unpowered before removing parts for washing.
  4. Turn over onto soft padding Support and lift the robot, turn over in the air, then lower gently onto soft padding, bottom up.
  5. Press the latch and remove the main brush cover Press and hold the main brush cover latch. Lift the unlocked cover off and set aside.
  6. Remove the main brush Grip and lift the main brush out of its compartment completely before moving aside.
  7. Clean the main brush Remove tangled hair from the main brush and wipe with a damp cloth. Clean every two weeks and replace every 6–12 months.
  8. Reinstall the main brush After cleaning and air-drying, move the main brush above its compartment and lower into its original position.
  9. Press the main brush cover firmly in place Align and replace the cover over the brush compartment. Press firmly down until the latch locks and the cover sits flat.
  10. Remove the side brush screw Fit a small screwdriver into the original screw at the side brush center. Loosen counterclockwise, remove, and save.
  11. Remove and clean the side brush Remove the side brush and clear hair from the bristles and shaft. Clean monthly and replace every 3–6 months.
  12. Reinstall the side brush Align and reinstall the side brush on its original shaft. Return the original screw to the center hole.
  13. Tighten the side brush screw Tighten the original screw clockwise with a small screwdriver and check that the side brush is secure.
  14. Wipe the robot sensors Wipe the docking locator and underside cliff sensors with a soft dry cloth.
  15. Pry out the swivel caster axle Pry out the swivel caster axle with a small screwdriver, then remove the wheel and axle. Leave the bracket on the robot.
  16. Wash the swivel caster Rinse the wheel and axle, remove hair and dirt, and air-dry completely before reinstalling.
  17. Reinstall the swivel caster Once the wheel and axle are completely dry, align with their original positions and press back in. Check that they seat.
  18. Wipe the main wheels clean Wipe dirt off both main wheel surfaces with a soft dry cloth.
  19. Turn the robot back over Support and lift the robot, turn right side up, then lower gently onto a flat floor.
  20. Remove the combined module Press and hold the release button and pull out the combined dustbin/water tank, supporting underneath.
  21. Open the module cover Support the combined module and lift its cover to expose the dustbin interior.
  22. Empty and clean the dustbin Empty the dustbin into a trash can and clear remaining dirt inside.
  23. Drain the water tank Open the water tank plug, drain remaining water, and air-dry the tank immediately after mopping.
  24. Close the dried water tank Drain and air-dry the water tank, then press the plug back and check the seal.
  25. Close the cleaned module After cleaning the dustbin, lower the cover and press along its edges.
  26. Reinstall the cleaned module Reinstall the combined module with the mop bracket in the robot. Check that the release button returns to position.
  27. Remove the mop bracket Press and hold the bracket latch, remove the mop bracket, and move clear of the combined module.
  28. Remove and wash the mop cloth Peel the mop cloth off the bracket, wash, and air-dry thoroughly. Clean after each use and replace every 3–6 months.
  29. Remove the module again Before washing the filter, press and hold the release button and remove the combined module again, supporting underneath.
  30. Open the cover and remove the filter Lift the combined module cover to expose the filter holder and latch.
  31. Press the latch and remove the filter holder Keep the module cover open. Press the filter holder latch and remove the entire holder outward.
  32. Remove the filter Grip the filter frame and remove from the holder without touching the filter media.
  33. Rinse and air-dry the filter Rinse repeatedly with clean water and tap gently to remove dirt. Air-dry at least 24 hours and reinstall only when completely dry.
  34. Reinstall the filter holder Once completely dry, return the filter to its holder and reinstall the holder in the module. Check that the latch locks.
  35. Close the water tank Confirm the water tank is drained and dry, then press the plug back firmly around the edges.
  36. Close the module cover Lower the module cover and press closed. Check its edges are flush without lifting.
  37. Reinstall the combined module Reinstall the dry combined module. Check that the release button returns and the module locks securely.
  38. Open the auto-empty dock's top cover When the dust bag is full, open the dock top cover to expose the bag handle.
  39. Lift out the old dust bag Lift the dust bag by its handle. Remove completely and discard.
  40. Wipe the dock filter Wipe the filter inside the dust compartment with a dry cloth. Do not rinse with water.
  41. Install the new dust bag Insert the new dust bag fully into its original mount, then close the dock top cover.
  42. Wipe the dock contacts Wipe the dock beacon and charging contacts with a soft dry cloth.
  43. Wipe the robot contacts Lift and turn the robot over onto soft padding. Wipe the underside charging contacts with a soft dry cloth.
  44. Reconnect power after installation Confirm all parts are secure and completely dry. Turn the robot upright and reconnect the dock plug.
  45. Return to the dock to charge Place the robot on the dock. Confirm the power light pulses and charging starts.