Loading 3D model
Tap here
Drag to rotate · Right-click or two fingers to pan · Scroll or pinch to zoom · Tap a part for details

All done

FAQ

Stuck?
Start here.

These are the issues buyers run into most when assembling. Tap one to jump to that step in 3D.

All steps

Assemble

  1. Position the main unit Place the main unit on a firm, flat, level floor with a protective mat. Leave at least 7.87 ft (240 cm) behind and 1.97 ft (60 cm) on each side.
  2. Check the parts Check the main unit, safety key, 0.68 fl oz (20 ml) silicone oil, and S5/S6 keys; 4 M8×40 bolts, 2 M8×15 bolts, and 6 D8 washers.
  3. Raise both uprights Steady uprights A2/A3 and slowly lift with the console assembly until the base bolt holes align.
  4. Fit the left-side washer Slide the 2 D7 serrated washers onto the M8×40 bolts, one each, until seated beneath the heads.
  5. Insert the left-side bolts Insert 2 M8×40 bolts from outside the left side inward. Give them a few turns by hand; do not fully tighten yet.
  6. Tighten the left-side bolts Tighten each clockwise with the F2 S5 hex key until the uprights are secure without wobbling.
  7. Fit the right-side washer Slide the 2 D7 serrated washers onto the M8×40 bolts, one each, until seated beneath the heads.
  8. Insert the right-side bolts Insert 2 M8×40 bolts from outside the right side inward. Give them a few turns by hand; do not fully tighten yet.
  9. Tighten the right-side bolts Tighten each clockwise with the F2 S5 hex key until the uprights are secure without wobbling.
  10. Fold the console assembly down Support console assembly G3 and rotate down around the upper upright pivots until the side mounting holes align.
  11. Fit the left console side washer Slide 1 D7 serrated washer onto the M8×15 bolt until seated beneath the head.
  12. Insert the left console side bolt From between the two uprights, insert 1 M8×15 bolt outward from the inner side facing the running belt. Give it a few turns by hand; do not fully tighten yet.
  13. Tighten the left console side bolt Tighten each clockwise with the F2 S5 hex key until the console mount is secure without wobbling.
  14. Fit the right console side washer Slide 1 D7 serrated washer onto the M8×15 bolt until seated beneath the head.
  15. Insert the right console side bolt From between the two uprights, insert 1 M8×15 bolt outward from the inner side facing the running belt. Give it a few turns by hand; do not fully tighten yet.
  16. Tighten the right console side bolt Tighten each clockwise with the F2 S5 hex key until the console mount is secure without wobbling.
  17. Flip up the panel Grip the top edge of panel G1 and rotate upward around the lower pivot to the normal viewing position.
  18. Snap on the safety key Align the C19 safety key magnet with the center console sensing position and attach firmly.
  19. Cut off the shipping tie Confirm all upright and console bolts are tight before cutting and removing front deck shipping tie F.

Fold and store

  1. Turn off the power after it stops completely Confirm the belt has stopped completely before turning power switch E17 off.
  2. Unplug the power cord Grip the plug body and pull straight out of the outlet. Keep the cord clear of the gas cylinder, wheels, and other moving parts.
  3. Remove the safety key Remove the C19 magnet from its sensing position and store it with the clothing clip out of children's reach.
  4. Lift and lock the deck Stand at the rear and grip both G points. Lift until gas cylinder B7 locks, then check that the deck stays up.
  5. Unlock and lower the deck Hold rear end G with both hands. Gently press the center release sleeve on gas cylinder B7 with your foot, guiding the deck slowly all the way down.
  6. Fold again before moving Stand at the rear and grip both G points. Lift until gas cylinder B7 locks, then check that the deck stays up.
  7. Brace the wheel and tilt to move Hold both sides of folded deck end G with both hands. Brace your foot at transport wheel I, tilt the unit toward yourself, then move it on the wheels.
  8. Return to the operating position Keep holding end G with your foot braced at wheel I. Tilt and roll back onto a firm, level floor, leaving 7.87 ft (240 cm) behind and 1.97 ft (60 cm) on each side.
  9. Lower completely before use Hold rear end G with both hands. Gently press the center release sleeve on gas cylinder B7 with your foot, guiding the deck slowly all the way down.

Adjust the incline

  1. Lift the rear end to remove the load Stop and unplug. Hold rear end G with both hands and lift slightly until both C20 adjustment feet clear the floor.
  2. Pull out the left locating pin Keep the deck supported. Grip the left B9 pin ring and pull straight outward until the pin clears the locating hole.
  3. Rotate the left adjustment foot Grip left adjustment foot C20 and rotate around its upper pivot to a lower setting until the selected locating holes align.
  4. Reinsert the left locating pin Insert the left B9 pin from outside inward through the aligned holes until the ring is close to the adjustment foot. Check it cannot slide out.
  5. Pull out the right locating pin Keep the deck supported. Grip the right B9 pin ring and pull straight outward until the pin clears the locating hole.
  6. Rotate the right adjustment foot Grip right adjustment foot C20 and rotate around its upper pivot to a lower setting until the selected locating holes align.
  7. Reinsert the right locating pin Insert the right B9 pin from outside inward through the aligned holes until the ring is close to the adjustment foot. Check it cannot slide out.
  8. Set securely and check both sides Confirm both sides use the same setting and pins are fully inserted. Slowly lower the rear until both adjustment feet touch the floor together.

First use

  1. Confirm the deck is lowered Confirm the deck is fully lowered and both adjustment feet on the floor, then check that the power plug is removed.
  2. Lift the left side of the belt Lift the middle edge of the belt on the left to expose the running board. Keep that side raised and the other side still.
  3. Lubricate the left side of the running board Keep the left side of the belt raised. Insert the F3 silicone oil bottle nozzle from the side and squeeze oil onto the running board.
  4. Lower the left belt edge Withdraw the nozzle and slowly lower the left belt edge onto the running board.
  5. Lift the right side of the belt Lift the middle edge of the belt on the right to expose the running board. Keep that side raised and the other side still.
  6. Lubricate the right side of the running board Keep the right side of the belt raised. Insert the F3 silicone oil bottle nozzle from the side and squeeze oil onto the running board.
  7. Lower the right belt edge Withdraw the nozzle and slowly lower the right belt edge onto the running board.
  8. Verify the power supply, then plug in Confirm 120 V power and a correctly grounded outlet matching the original three-prong plug. Insert straight in fully.
  9. Turn the power switch on Flip rocker switch E17 beside the power cord to On and confirm the console powers up.
  10. Retrieve the key and clothing clip Retrieve the safety key and clothing clip. Bring the clip to the clothing edge, holding the magnet just outside the sensing position for now.
  11. Secure the safety clothing clip Squeeze clothing clip C19 open, place the clothing edge inside, and release to grip. Then attach the magnet to the sensing position.
  12. Start with a slow walk Stand on the side foot rails, hold the handrails, and press START. The belt starts at 1 mph. Step on and walk slowly once comfortable.
  13. Pull the key for an emergency stop For an emergency stop, pull C19's magnet outward off the console. The belt stops and "---" appears.
  14. Reattach the safety key magnet Confirm the belt has stopped completely before returning the magnet to the sensing position. Press START to restart.
  15. Start the belt again Keep both feet on the side foot rails and press START again. The belt starts at the default low speed.
  16. Use the button to pause and end Press STOP/PAUSE once to pause and keep the data. Press again to end the workout and clear the data.